Mounting

Ahlsell is one of the largest distributors within fastening to the Swedish market. We have fastenings for all purposes – from small installations to nuclear power plants and smart storage solutions to help you keep order in place. We have a generous standard range for those who need fastenings for the construction job, industrial projects, installation assignments, or real estate projects.

Ahlsell's Fastening range consists of market-leading brands and partners. Ahlsell's own brand FIXX forms a large part of the range.

Masonry anchor BLS Superplus
Sormat
Masonry anchor BLS Superplus
Art. no.: 298392
BLS - Zinc-plated. European type approved, ETA 01/0011 Option 1- cracked and uncracked concrete.
Self-undercutting hook anchor with stud bolt, nut/washer. Steel quality 8.8.

Superplus is a self-undercutting hook anchor for large loads that does not require special tools or special drills. The unique properties of Superplus are that it makes undercutting automatic just by applying the recommended tightening torque during installation. When the recommended tightening torque is achieved, the cone has slipped into the slotted part of the sleeve that is expanded and the teeth on the coupling have pierced the base material and are made the undercutting/hood effect.

Superplus has ETA approval for option 1, so it may also be used in cracked concrete (tension zone). Typical application areas are nuclear power plants, mechanical mounting, ground bolts, etc. indoors, where a high level of safety and a high tensile and transverse load capacity is demanded (safety class 3). Superplus is available in three different sizes, M8, M12, and M16, with several different setting depths. Superplus is also available in an acid-proof steel A4 version, with type approval ETA-05/0013.

Permitted loads, kN in concrete C20/25
Expansion anchor s-ka zpl
Sormat
Expansion anchor s-ka zpl
Art. no.: 233383W
S-KA- Zinc-plated. European type approved, ETA 08/0173 Option 1- cracked and uncracked concrete.
S-KA through cut expander is a torque tightened expander for use in cracked and uncracked concrete. It can also be used for installation in homogeneous substrate as full brick (but max M8)) and natural stone. The expander is of even thickness and can therefore be installed directly through the component. It can be used indoors and in mostly dry areas.

1) Drill a hole according to the table in the mounting data below 2) Using a brush and blow pump, clean the hole 3) Push in the expander 4) Tighten the expander to the recommended torque.

I) Permitted loads, kN in concrete C20/25.
* Not covered by the ETA values recommended by the manufacturer.
Cross load values apply to attachment without concrete edge impact.
Lockwasher nordlock nl
Nord-Lock
Lockwasher nordlock nl
Art. no.: 289184
Lock washer Nord-Lock In accordance with DIN 25201. Acid-resistant material equivalent A4-quality.
Nord-Lock consists of pairs of pre-assembled washers with combs on an incline on one side where the comb angle is greater than the angle of the thread increase and there are radial teeth on the opposite side. The washers are always mounted in pairs with the comb sides towards each other.

When the screw/nut is tightened, the Nord-Lock washer grips the opposite surfaces, allowing movement only movement along inclined combs. Each attempt to unscrew a screw/nut will be effectively blocked by the kill locking that will take place.
The Nord-Lock safety washers have an outer diameter adapted for recessed holes as standard. In addition, there are washers with enlarged outer diameters (SP) for use with large/oblong holes, painted surfaces or soft materials such as aluminium. Use Nord Lock SP washers in combination with the flange screw/nut for maximum load distribution.

Nord-Lock screw fusing system can also be used for high strength screws/nuts. Straight through holes require two pairs of washers, both under the head of the screw and under the nuts. Nord-Lock also effectively secures the nut to the stud bolt and eliminates the need for locking fluid.
Lockwasher nordlock nl
Nord-Lock
Lockwasher nordlock nl
Art. no.: 289146
Lock washer Nord-Lock in accordance with DIN 25201. Surface treated with Delta Protekt (complies with RoHs and ELV) and manages up to 600 hours in salt spray test in accordance with ISO 9227. Nord-Locks steel washers are made of EN 1.7182 or equivalent steel. All steel washers are tempered/through hardened. Also available in acid-resistant material equivalent to A4-quality.

Nord-Lock consists of pairs of pre-assembled washers with combs on an incline on one side where the comb angle is greater than the angle of the thread pitch and radial teeth on the opposite side. The washers are always mounted in pairs with the comb sides towards each other.
When the screw/nut is tightened, the Nord-Lock washer grips the opposite surfaces, allowing movement only movement along inclined combs. Each attempt to unscrew a screw/nut will be effectively blocked by the kill locking that will take place.

The NOrd-Lock safety washers have an outer diameter adapted for recessed holes as standard. In addition, there are washers with enlarged outer diameters (SP) for use with large/oblong holes, painted surfaces or soft materials such as aluminium. Use Nord Lock SP washers in combination with the flange screw/nut for maximum load distribution.

Nord-Lock screw fusing system can also be used for high strength screws/nuts. Straight through holes require two pairs of washers, both under the head of the screw and under the nuts. Nord-Lock also effectively secures the nut to the stud bolt and eliminates the need for locking fluid.
Showing 52 of 1009